What did you do to your Bronco today?

Out for a little fun.

Installed some Hella 500 Amber Lights. Oh, an onboard air compressor as well!

joshyboy691

I put on the Mabett backset protector. I would definitely recommend getting these as they are inexpensive and if you want to protect the back of the seat. For me, I go camping and some of the gear can have the sharp edges and I really don't feel like tearing up my seats right off the bat lol

Awesome addition! This was the 2nd mod I did. Absolutely LOVE this

Small front end adjustment today!! ?

Today I finished the next phase of my build. I added a DV8 OE series front bumper and a DV8 FS-15 series rear bumper. I considered trying it myself but I also added DV8 elite series fog lights in the front and flush pods in the back. I've never done any wiring myself and decided to leave the whole thing to professionals. Really pleased with how it came out

Installed the Flowmaster Outlaw axle back exhaust last night. EASY install and great sound

Just added the Aeroskin from ford. Adding the oracle light for the back hatch next.

Did a sweet trail ride with my Tri-State Bronco buds...

went to a Cars and Coffee event with the local Bronco club -

Finished adding the oracle light.

Here's a good night shot with it off vs on.

Went out lookin for VIPs in Da Short Bus!

Broncobsessed

Installed the Flowmaster Outlaw axle back exhaust last night. EASY install and great sound

Im want to install one as well. Can I ask what site you bought it from?

Mandogus

Im want to install one as well. Can I ask what site you bought it from?

I originally ordered from NAPA, but it was on backorder so I cancelled and ordered from 4WP. That also ended up getting backordered because of supply chain constraints. Even with all the waiting, I’m very happy with the product.

I installed some gas shock hood struts I bought for $29 off of Amazon:
https://smile.amazon.com/dp/B0B9B6F7MS?psc=1&ref=ppx_yo2ov_dt_b_product_details
They didn’t come with any instructions, but they install like most of the other ones, so I watched a competitors video.
A few notes:
1) The square nut was not threaded very well, so I ran the screw in and out of each nut a few times before installing them.
2) I used blue Locktite on the hood screw.
3) The metal install wand needs to be bent so that the nut is flat behind the hole.


They seem to work just fine.

Shut off the fake engine noise in the DSP module on B&O Lux models w/Forscan (783-01-01 C***-****-****) . Made a noticeable difference, though not enough to register on my db meter.

I'm patiently waiting on my Bronco and decided to venture over to interactivegarage.com and build out the mods to my eventual Bronco. The only visible difference is that I'm undecided on the lightbar. I love the way it looks, but I'm not sure I want to drop the money when I'll most likely not use it for anything other than aesthetics.

You know the end of the mod cycle (for the time being) is near when you go with the Bronco Buddy...

New here so I'll have to play catch-up. Here's what i've done over the last 9 months.
Interior:
BYB Accessory Rail, Door pockets, Wireless charger, DIY rear platform
Exterior:
Zone 3" Adventure lift, 37" Ironman M/Ts, Method 312s (-12mm offset), XBull 13.5k winch on an RC winch plate, JCR tailgate reinforcement/reloc, FabFours Rock Sliders, Rigid fogs and ditch lights, DV8 inner fenders and LCA skids, ASFIR gearbox and x-fer case skids, Nextventure Read Diff skid, BroncoBuster tie-rod braces and rear shock skids. Waiting on Oracle bi-led headlamps (w/amber ring) and 4WP fender deletes.